Updated: How to sound like a Pro when operating on a repeater

New and improved! How to sound like a pro when operating on a repeater and the companion guide: How to Participate in a Net like a Pro!

repeater guidelines
How to sound like a pro when operating on a repeater

How to sound like a pro when operating on a repeater was written in an effort to help Elmer newly-licensed hams (and those who may or may not have a CB background) on common conventions used when operating on repeaters. None of us are perfect and even long-time hams slip up now and then, but we hope that this guide will help you sound like a pro when operating on repeaters.

The guide provides positive guidelines, and lays out common nomenclature used by convention on repeaters. There are no hard and fast rules. Your ham license won’t be revoked, no one is going to laugh and point, but you are more likely to get a positive response when you sound like you know the lingo and use it appropriately.

See the companion document: How to Participate in a Net like a Pro!

BrandMeister Explained

Bill Rinker, W6OAV
Bill Rinker, W6OAV

By Bill Rinker, W6OAV

This article is for BrandMeister users who are somewhat familiar with the DMR protocol. This article does not go into explaining the DMR protocol. That information is provided in the links listed at the end of this article.

BRANDMEISTER VERSES DMR MARC

Before beginning, definitions must be made:

  • Time Slots – There are two digital time slots on a DMR repeater which provide two independent voice channels.
  • Talk groups – Independent “voice channels” available in each time slot.
  • Code Plug – A radio’s configuration file.
  1. What are the differences between C-Bridge and BrandMeister?

The major difference between C-Bridge and BrandMeister is that BrandMeister allows a local user to key up and route any desired talk group whereas the C-Bridge network only allows a local user to key up and route talk groups as defined by the C-Bridge sysop.

Both Networks have static talk groups and dynamic talk groups. Definitions:

Static Talk group – A talk group which is always active meaning that DMR network traffic is always sent to the repeater on a designated time slot without any user intervention. Static talk groups are configured in the network and cannot be modified by the local user. A local user can only key up static talk groups that are configured on the repeater.

Dynamic Talk group – A talk group which only sends DMR network traffic to the repeater when a local user keys up that talk group. The talk group network traffic will be sent to the repeater for a period of 15 minutes after the most recent key up by the local user. A BrandMeister local user can key up any of the many available talk groups. The local user’s code plug programming controls talk group access.

In some cases, there are different equivalent talk groups between the two networks. For example, most C-Bridges use TG 1 as their worldwide talk group whereas the BrandMeister worldwide talk group is 91. However, some talk groups are shared and cross-connected.

  1. Why don’t I hear as much talk group traffic on a BrandMeister repeater as I do on a C-Bridge repeater?

As described above, unlike a C-Bridge repeater which carries “always on” traffic, a BrandMeister time slot will not carry talk group traffic until a local user keys up a talk group.

BRANDMEISTER QUESTIONS

  1. Where can I find a list of talk groups?

Good sources are:

https://www.dmr-utah.net/talkgroups.php
https://k5nsx.com/wp-content/uploads/US_BM_User_Guide.pdf

  1. How can I monitor BrandMeister talk groups?

Using a computer, iPad, or smart phone, access the BrandMeister Dashboard at https://hose.brandmeister.network/scan/. See Figure 1. Click the Scanner button at the top to display all the active talk groups.

Figure 1. Displaying all active talk groups.

To scan and listen to a particular talk group, or scan and listen to a set of talk groups, enter the talk group number(s) in the talk group list and click “Apply”. Figure 2 illustrates scanning and listening to talk groups 3100 (USA) and 3108 (Colorado).

you can scan and listen to talk groups on the brandmeister website
Figure 2. Scanning and listening to Talk Groups 3100 and 3108.

If you hear a conversation that is of interest, key up that talk group (if it is in your code plug) and join the group! Note the Dashboard VU meter and spectrum display. These are great for checking your transmitter audio.

Another benefit of the scanner is that one can listen to various talk groups and decide which interesting ones to add to the code plug.

  1. Why is my Channel Busy LED on but when scanning I don’t hear any talk group traffic?

A local user may have keyed up one of the many talk groups that aren’t in your radio’s code plug.

BRANDMEISTER TALK GROUP KEY UP PROCEDURE

Due to the nature of dynamic talk groups specific procedures must be used when keying up a talk group. If done improperly several different issues can occur:

  • A local user keying up a talk group can isolate another local user from a talk group he was using.
  • A local user can key up a talk group and disrupt an existing conversation on that talk group.
  • A local user can key up multiple talk groups on the same time slot which can possibly create talk group chaos.

Key Up Procedure

Before keying up a talk group, monitor the Channel Busy LED for at least a minute. If the LED doesn’t light then both time slots are idle. Key up your desired talk group. Then listen for at least a minute before transmitting to determine if the talk group is busy. The reason for listening is because if a remote talk group user is transmitting when you keyed up the talk group, you will not hear his audio nor will the Channel Busy LED light. You will hear audio, and the Channel Busy LED will light, when the next remote user begins transmitting.

If the Channel Busy LED is on, or flashes on and off, then one or both of the time slots are busy. To determine if your desired time slot is idle or busy, wait until the Channel Busy LED is on and then key up your talk group. If a busy tone results, then your desired time slot is busy. Do not key up again until the Channel Busy LED has been off for a minute indicating that the time slot is now idle. The Channel Busy LED will turn off and then back on between long conversation “overs”.

If keying up while the Channel Busy LED is on results in a “connect confirmation tone”, then your time slot is idle and your talk group has been activated. As mentioned above, listen before transmitting.

 

REFERENCES

Amateur Guide to DMR – https://www.dmr-utah.net/media/Amateur_Radio_Guide_to_DMR.pdf

What is BrandMeister? – https://wiki.brandmeister.network/index.php/What_is_BrandMeister

BrandMeister User’s Guide – https://k5nsx.com/wp-content/uploads/US_BM_User_Guide.pdf

BrandMeister getting Started Guide – n8noe.us/DMR/files/BrandMeisterGettingStartedGuide.pdf

 

The RMRL goes digital!

Announcing RMRL’s very first DMR repeater! It’s now on the air from Guy Hill on RMRL’s 449.750 repeater frequency. This Motorola SLR5700 is on the Brandmeister network. Try it out!

449.750
Color Code 1
Talkgroup 310894
Timeslot 2
See below for further details.

Rocky Mountain Radio League's digital repeater
Rocky Mountain Radio League’s Motorola SLR5700 digital repeater. Join us on the 449.750!

If you have a TYT digital radio, we are looking for someone who can be our “go to” person to help other club members program their radios.

If you have a Motorola digital radio, contact Becky at . Include your name, call sign, and telephone number. We will put you in touch with someone who has the Motorola programming software (and knows how to use it) and will meet you at HRO to program your radio.

Thanks to everyone who worked to bring it online, including Mike, KI0GO, Glenn WN0EHE, and Dunnigan K1DUN.

RMRL digital repeater
Mike dives into the repeater cabinet to get things connected.
Mike programmed and installed the repeater. Thank you, Mike!

If you want to start out with a sample codeplug, try the RMHAM site, and proceed as follows:

  1. In your codeplug, create a contact and RX group for talk group 310894
  2. Create a new channel in your codeplug for accessing to the 310894 talk group via RMRL’s DMR repeater.
  3. Set the new channel parameters to 449.750 on RX, 444.750 on TX, time slot = 2, color code = 1, and RX group is the one you created that includes the 310894 contact.
  4. Set other channel parameters as desired.

Follow steps 1-4 for any other talkgroup(s) you’d like to access through RMRL’s DMR repeater but use time slot 1 instead of 2.

The basics of BrandMeister explained.  Here is the BrandMeister dashboard, and here is the BrandMeister Hoseline.

MD-380 tweak.

5 in 1 weather sensor atop Squaw Mountain

These photos show the mounting location of the final enhancement to our existing RMRL weather station located atop Squaw Mountain, home of two of our very popular club repeaters.

The new 5 in 1 sensor will now provide us with the ability to track wind speed, wind direction, temperature, humidity and precipitation amounts at an elevation of 11,460′. In addition, we also have three temperature/humidity sensors located in our repeater rack room. All sensors can be viewed in “real time” throughout our website under the heading “Squaw Mountain Weather.”

5 in 1 weather sensor on Squaw Mountain
5 in 1 sensor atop the House of Radios on Squaw Mountain. Tracks wind speed, wind direction, temperature, humidity and precipitation.

 

Squaw Mountain weather station.
The Rocky Mountain Radio League’s weather sensor on Squaw Mountain.

Thanks go to Kevin, KD0VHD, and Willem, AC0KQ, for their contributions to the Rocky Mountain Radio League. The sensor was installed August 10, 2017.

Please report any repeater problems

Please report any repeater problems immediately.

It is easier than ever to report a problem with a RMRL repeater. The new REPEATER PROBLEM REPORT form can be found on the three repeater pages as well as the Contact Us page. If you look on the main Repeater Page (Menu item RMRL Repeaters) and find the status of a repeater is ‘Up’ but you encountered a problem, then please fill out a Repeater Problem Report immediately.

We appreciate your help!

Here, for your convenience, is our new Repeater Problem Report form.  (Note: we are asking for your name and e-mail address in case we need to contact you for clarification.)

    Your Name (required)

    Your E-mail (required)

    Select Repeater (required)

    Please describe the problem